+86-15123173615

Causes of Engine Oil Consumption

Feb 14, 2026

Reference for dealing with the problems of high engine oil consumption and in car maintenance.

 

1. External Oil Leakage

There are many reasons for oil leakage, including: oil lines, oil drain plugs, oil pan gaskets, valve cover gaskets, oil pump gaskets, fuel pump gaskets, timing chain cover seals, and camshaft seals. All the above possible leakage factors should not be ignored, as even a small leakage can lead to a large amount of oil consumption. For example, if one drop leaks every six seconds, it means 0.56 liters of oil are consumed per 100 kilometers. The best way to check for leaks is to place a light-colored cloth under the engine, start the engine, and check. The location of the oil drops on the cloth can help determine the leakage point.

 

2. Front and Rear Oil Seal Failure

Damage to the front and rear main bearing oil seals will definitely cause oil leakage. This situation can only be detected when the engine is under load. Worn main bearing oil seals must be replaced because, like external oil leakage, they can cause a large amount of oil to leak.

 

3. Main Bearing Wear or Failure

Worn or faulty main bearings will throw excessive oil onto the cylinder walls. As the bearing wear increases, more oil will be thrown. For example, if a bearing design clearance of 0.04 mm can provide normal lubrication and cooling functions, and if the bearing clearance can be maintained, the amount of oil thrown will be normal, and the bearing will not be damaged. When the clearance increases to 0.08 mm, the amount of oil thrown will be five times the normal amount. If the clearance increases to 0.16 mm, the amount of oil thrown will be 25 times the normal amount. If the main bearing throws too much oil, more oil will splash onto the cylinder, making it difficult for the piston and piston rings to effectively control the oil. This will lead to oil burning or the formation of carbon deposits on the piston and piston rings. Usually, if too much oil is lost at the main bearing, the connecting rod bearing will lack oil, resulting in insufficient oil splashed onto the cylinder wall at certain low speeds, causing wear of the piston ring and piston, and making it impossible to control the oil when the engine is running at high speed. Therefore, the consequence of main bearing wear is high oil consumption.

 

4. Connecting Rod Bearing Wear or Damage

The effect of connecting rod bearing clearance on oil is similar to that of main bearing wear. In addition, the oil is more directly thrown onto the cylinder wall. Worn or damaged connecting rod bearings cause excessive oil to be thrown onto the cylinder wall, making it difficult for the piston and piston rings, which are designed to control normal oil volume, to effectively control the excessive oil, thus allowing the excess oil to enter the combustion chamber and be burned, resulting in high oil consumption. Note: Insufficient bearing clearance not only leads to its own wear but also causes wear of the piston, piston rings, and cylinder walls.

 

5. Camshaft Bearing Wear or Damage

Camshaft bearings are usually pressure-lubricated. If the clearance is too large, excessive oil will be lost. The lost oil will soak the valve guide and valve stem, increasing oil consumption.

 

6. Crankshaft Journal Wear

The effect of crankshaft journal wear on oil is the same as that of bearing wear. When it becomes out of round, the clearance between it and the circular bearing will be uneven. The size of the clearance between the out-of-round crankshaft journal and the bearing changes during rotation, causing more oil to be thrown. Out-of-round bearings need to be reground and paired with smaller-sized bearings. For cylinders that are ground to a slight taper and out of round (reduced cylindricality and concentricity), oil consumption can be controlled by the piston and piston rings. However, as the taper and out-of-roundness of the cylinder increase, it becomes increasingly difficult to control oil consumption. This is the result of many factors combined. As the clearance between the piston and the cylinder increases, the piston will swing during operation; this instantaneous tilting swing will cause excessive oil to accumulate on one side of the piston, and the same situation also occurs on the piston rings. In this way, as the piston keeps swinging back and forth, some engine oil will seep into the combustion chamber. For each revolution of the crankshaft, the piston completes two strokes, one up and one down. When the engine is running at 3000 rpm (approximately 60 miles per hour), the piston rings running in the deformed cylinder liner will undergo 6000 size and shape changes per minute. As a result, at high speeds, the piston rings may not be able to adjust their fit clearance with the cylinder liner in time (especially when running over the worn part of the cylinder liner, causing excessive fit clearance). Therefore, whenever the above situation occurs, it will lead to excessive oil consumption of the engine.

 

7. Deformation of cylinder liner

There are other reasons for cylinder liner deformation, such as uneven heating or uneven tightness of the cylinder head bolts, which can cause the cylinder liner to twist and deform, resulting in the piston rings being unable to form an appropriate fit contact with the cylinder liner surface, reducing the oil scraping function; as a result, excessive oil is left in some areas and eventually seeps into the combustion chamber and is burned, causing an increase in oil consumption.

 

8. The positive pressure ventilation valve or pipe of the "PCV" blocked

The main function of the PCV (Positive Crankcase Ventilation) is to recycle the mixed gas that has seeped from the engine combustion chamber into the crankcase, reducing the content of unburned hydrocarbons. The seeped mixed gas is a mixture of air, fuel, and combustion exhaust. During the power stroke, due to high pressure, it seeps into the crankcase through the gap between the piston/piston ring and the cylinder liner. The PCV system usually has a pipe that connects the crankcase to the carburetor or intake manifold. The vacuum generated in the engine intake manifold when the intake occurs will suck the mixed gas from the crankcase and return it to the combustion chamber for reuse. The PCV (Positive Crankcase Ventilation) valve may be blocked by sludge, varnish, or other impurities in the mixed gas. This will cause the engine oil to deteriorate, generating excessive deposits, resulting in the piston rings (oil rings) being blocked, increased oil consumption, and premature wear of the piston rings; increased crankcase pressure, leading to the failure of the crankshaft seal, oil leakage, and deterioration of engine performance.

 

9. Grinding Abrasive Wear

If the cylinder liner has been ground or polished, it must be cleaned strictly in accordance with the requirements to prevent residual metal debris or abrasives from damaging the surface of the piston ring groove. The cleaning method is as follows: After grinding, the cylinder liner must be thoroughly cleaned with a brush dipped in soapy water and then immediately oiled; or clean the cylinder wall with 10# lubricating oil and carefully wipe it clean. Repeat the above process until all foreign matter is removed. Regardless of which method is used, a final inspection is required: wipe the cylinder liner surface with a white cloth. If the white cloth remains clean after wiping, it indicates that the cylinder liner has been cleaned properly.

Note: Do not use gasoline or kerosene to clean the ground cylinder wall. Because they cannot remove the abrasives adhering to the cylinder wall and will carry them into the micro-holes of the grinding texture. Therefore, a cylinder liner that has not been properly cleaned may cause premature wear, piston ring failure, and ultimately lead to increased oil consumption.

 

10. Piston Ring Groove Wear

The flatness of the end face of the piston ring groove and the correct clearance between the piston ring and the piston ring groove are important factors for the piston ring to perform a good sealing function. Generally, the side clearance of the piston ring groove in a car engine should not exceed 0.002" - 0.004". When the piston moves up and down, the piston ring must be properly seated in the piston ring groove. If the piston ring groove is deformed, it will cause the piston ring to fail to work properly, and engine oil will seep into the combustion chamber. A worn piston ring groove will cause the side clearance to increase, resulting in excessive engine oil seeping into the combustion chamber. Conversely, excessive side clearance will cause the piston ring to collide with the piston ring groove, further wearing the piston ring groove. If the situation is not improved, it may even cause the breakage of the piston ring land.

 

11. Damage or fracture of the piston ring land

If the piston ring land is damaged or fractured, the piston ring cannot be properly seated in the piston ring groove, resulting in excessive oil entering the combustion chamber. Additionally, it will lead to the complete damage of the cylinder liner, piston, and piston ring. Therefore, it is necessary to pay close attention. Once there are any signs, the parts must be replaced immediately.

 

12. Wear of the valve stem or guide

If the valve stem and guide wear, the vacuum suction force during intake will draw oil and oil vapor from the gap between the valve stem and guide into the intake manifold and eventually into the combustion chamber to be burned. If this situation is not improved, when the engine is equipped with new piston rings, the increased intake vacuum suction force will lead to increased oil consumption. When the engine undergoes major maintenance, the oil sludge and other deposits on the surface of the valve stem and guide are removed, and the gap will further increase, making the oil leakage loss more obvious. For overhead valve engines, both the exhaust and intake valves may experience oil leakage. For high oil consumption caused by excessive clearance between the valve guide and stem, it can be improved by continuously grinding the valve stem. Sometimes, new valves also need to be ground. The use of advanced integral bonded valve seals can effectively prevent oil leakage.

 

13. Bent or deformed connecting rod

A bent or deformed connecting rod will cause the piston to not move in a straight line along the cylinder liner, affecting the normal sealing function of the piston ring and increasing oil consumption. Additionally, a bent or deformed connecting rod will cause changes in the fit clearance between the connecting rod bearing and the piston pin, leading to premature wear of the connecting rod bearing and more oil being thrown onto the cylinder wall.

 

14. Worn or improperly positioned piston pin

If the piston pin is worn or improperly installed, the oil flowing towards the piston pin under pressure will be thrown onto the cylinder wall, and the piston ring cannot scrape off the excess oil. This not only leads to direct excessive oil consumption but also causes carbon deposits that can clog oil passages and cause the piston ring to seize.

 

15. Excessively tight piston pin fit

If the piston pin is installed too tightly at both ends, in the engine's repeated cold and hot working environment, the piston cannot expand and contract normally, leading to piston deformation and subsequent cylinder wall scoring, inevitably causing blow-by and excessive oil consumption.

 

16. Oil passage blockage

After long-term operation under harsh conditions, the engine generates carbon deposits and foreign matter that can easily block the oil passages in the piston and piston ring. At this point, the oil cannot return to the crankcase through the normal path but remains in certain areas such as the valve guide, increasing oil consumption. If the oil passage in the connecting rod or other parts is blocked, it will lead to poor engine lubrication, increased wear, and increased oil consumption. To prevent this, follow the prevention measures described in item 28. Of course, no additional clearance needs to be reserved.

 

17. Unbalanced torque of main bearing cap bolts or connecting rod bolts

If the torque of the main bearing cap bolts or connecting rod bolts is unbalanced, it will cause the bearing to become out of round and deformed, reducing the bearing's service life and causing excessive oil to be thrown out from the bearing, affecting oil consumption as described in items 3 and 4. When installing the bearing cap bolts, a torque wrench must be used and tightened strictly according to the manufacturer's specified torque. If the torque of the connecting rod bolts is unbalanced, it will cause the connecting rod to deform, with consequences as described in item 14.

 

18. Unbalanced torque of cylinder head bolts

The stress caused by unbalanced torque of the cylinder head bolts will lead to severe deformation of the cylinder and cause oil leakage as described in items 7 and 8. When installing the cylinder head bolts, a torque wrench must be used and tightened strictly according to the manufacturer's specified torque and sequence.

 

19. A dusty and dirty cooling system

Rust particles, scale, sediment or other products in the dirty cooling system water jackets and radiators, as well as corrosion in the water lines, will all negatively affect the cooling efficiency of the cooling system. The resulting cylinder deformation will directly cause oil loss, as described in items #7 and #8. Defects in the cooling system can cause the engine to overheat, and some cylinders may develop local hot spots, which can lead to scuffing and sticking of the cylinders, pistons and piston rings, resulting in increased fuel consumption. An overheated engine and an overall increase in the oil pan temperature can also cause fuel consumption to rise.

Send Inquiry