+86-15123173615

Engine air-to-air heat exchanger

Mar 02, 2026

The air-to-air heat exchanger is shaped like a coolant radiator and is usually installed on the chassis in front of the radiator (see Figure 12–28). When the vehicle is traveling on the road, ambient air is forced to flow through the fins and pipes. Thus, ram air serves as the cooling medium. When the vehicle is traveling at high speed, the air flow through the heat exchanger is at its maximum, and the cooling efficiency reaches its peak. When the air flow through the cooler is at its minimum (even if the engine fan may provide assistance), the efficiency is at its lowest. Therefore, air-to-air cooling may not be suitable for the operating conditions of construction machinery. Under the best conditions, the efficiency of an air-to-air heat exchanger is higher than that of any liquid-cooled heat exchanger. The best conditions mean that the air flow through the core is maximized, so the vehicle needs to be traveling at full speed. Figure 12–29 shows the typical position of a turbocharger intercooler in the engine compartment and the piping arrangement.

 

info-389-327

Figure 12–28 Front view of a typical intercooler.

 

info-409-392

Figure 12–29 Schematic diagram of the intercooler piping connection (showing the connection between the turbocharger impeller and the front-mounted heat exchanger).

 

Air-to-air intercooler testing

When the engine is running at near rated speed and load, the air temperature entering the intercooler is approximately 300°F (150°C). If an air-to-air heat exchanger is used, the outlet temperature of the boosted air should be approximately 110°F (44°C) when the ambient temperature is 75°F (24°C), but the specific values may vary slightly depending on the original equipment manufacturer (OEM). The design of the intercooler allows for a small amount of air leakage without affecting performance. When testing for leakage rate, the inlet and outlet of the intercooler should be blocked and pressurized to the test value recommended by the OEM. Some examples of OEM-recommended test values are as follows:

Engine OEM

Test Start Pressure

Allowable Pressure Drop in 15 Seconds

Caterpillar

30 psi

5 psi

Cummins

30 psi

7 psi

Detroit Diesel

25 psi

5 psi

 

If the pressure drop exceeds the specification, the pressure should be reduced to 5 psi and maintained, and then a soapy water solution should be used to locate the leakage point.

 

Dynamometer testing and intercoolers

When testing trucks equipped with air-to-air intercoolers on a chassis dynamometer, it is important to note that the lack of airflow in the engine compartment can significantly reduce cooling efficiency. The auxiliary fan of the dynamometer has a limited effect compared to the ram air effect that makes the air-to-air intercooler operate efficiently. Due to the lower efficiency of the intercooler under dynamometer test conditions, the measured peak brake horsepower (BHP) reading will be lower, and the exhaust nitrogen oxides (NOx) will increase. During the dynamometer test cycle, the peak BHP should be tested immediately after the coolant reaches the operating temperature, followed by other tests.

 

Aftercoolers and intercoolers

The terms aftercooler and intercooler usually refer to heat exchangers that use engine coolant as the cooling medium. They are synonyms, and the specific term used only reflects the preference of the OEM. The boosted air is forced through a core containing pipes, and the coolant of the engine cooling system circulates and is pumped through the pipes. Because the cooling medium itself has heat, its cooling efficiency is often lower than that of an air-to-air heat exchanger; such coolers are still used in scenarios where there is insufficient airflow in the engine compartment and air-to-air heat exchangers are not applicable. Some designs also use ram air as an auxiliary to the engine coolant.

 

Troubleshooting the boost circuit

When the manifold boost pressure is too high or too low, it can cause engine performance issues. Common causes of manifold boost pressure being lower than the specified value include:

• Air system blockage upstream or downstream of the turbocharger impeller

• Air leakage downstream of the turbocharger impeller

• Insufficient fuel supply

• Mismatched turbocharger

Common causes of manifold boost pressure being higher than the specified value include:

• Mismatched turbocharger

• Stuck VG turbo variable geometry ring

• Excessively high intake air temperature

• Fouling of the turbo housing or nozzles, exhaust ports, and turbine blades

• Excessive fuel supply due to ECM calibration issues, fuel injector leakage, intake system leakage, and sensor faults

• Advanced fuel injection timing

 

Warning:

When testing for boost side leakage, do not adjust the air pressure to more than 30 psi (200 kPa), as this may cause personal injury and damage to pressurized components.

Send Inquiry