+86-15123173615

Main Engine Jacket Water System: Working Principle and Related Operations

Nov 08, 2026

I. System Working Principle

The Main Engine Jacket Water System is a closed freshwater circulation temperature control system, primarily aimed at ensuring that the main engine operates within a suitable temperature range (typically the warm-up/run temperature is controlled at around 60°C to 75°C).

info-1080-1467

Main Engine Jacket Water System Water Valve Temperature Controller

 

1. Cooling Principle (Cooling)

When the main engine is running, it generates a large amount of heat. The hot freshwater flows out of the main engine, passes through the hot freshwater inlet pipe and enters the cylinder liner water cooler, where it exchanges heat with the cold freshwater (or seawater) to cool down. Then, it is returned to the main freshwater pump by the main freshwater pump to prevent the main engine from overheating.

2. Heating/Thermal Preservation Principle (Heating)

When the ship is at anchor and the main engine is not running, the system needs to drive the freshwater circulation through the cylinder liner water preheater pump, while also turning on the cylinder liner water heater for electric heating to keep the main engine body at a "warm cylinder" temperature, preventing components from experiencing thermal stress due to low temperature, and preparing for immediate vehicle start-up.

Reference: The purpose of warming the cylinder is to prevent the machine from directly igniting cold fuel and avoiding excessive thermal stress that makes it difficult to start. The warming methods include steam heating, electric heating, and auxiliary engine cylinder liner water heating. The chief engineer must know and be able to operate: Power operation should be known and mastered

 

info-1080-486

Main Engine Jacket Water System Water Preheater Pump

 

info-1080-486

Main Engine Jacket Water System Water Preheater Pump Inlet and Outlet Valves

 

info-546-1214

Main Engine Jacket Water System Water Heater

 

info-546-1213

Heater Control Box

 

info-1080-2400

Main Engine Jacket Water System Water Cooler

 

info-546-1214

Main Engine Jacket Water System Water Cooling Pump Start and Stop

 

info-546-1213

Main Engine Jacket Water System Water Cooler Hot Freshwater Inlet Valve

 

II. Main Engine Warm-up and Shutdown Operations (for the cylinder liner water system)

1. Warm-up Stage (Before Departure)

Purpose: To warm up the engine in advance to reach the start-up requirements (about 60~65°C or above).

Warm-up Operation:

Start the cylinder liner water preheater pump several hours in advance, turn on the cylinder liner water heater, and set the heater control box to "automatic" or manually turn on the heating to gradually increase the cylinder liner water temperature to the specified value (such as 70°C or so).

Note: The warm-up procedure has already been initiated.

Before the main engine is about to start, start the main freshwater pump (hot freshwater pump), open the hot freshwater inlet and outlet valves, and check if the cooling system and related pipelines are in normal condition.

After the main engine starts: Close/Stop the cylinder liner water heating heater, stop the cylinder liner water preheater pump,

Transfer to the normal cooling cycle mode led by the cylinder liner water cooler, and continuously monitor the temperature to maintain around 70°C to 75°C.

2. Shutdown Stage (After Departure)

Purpose: To remove the residual heat from the main engine and then re-heat for rust prevention.

Shutting down and turning the engine: After the main engine is shut down, open the indicator valve, and turn on the turning gear machine for 10~15 minutes (to remove excess heat).

Stop the main pump: After turning the engine, stop the main freshwater pump (hot freshwater pump), close the hot freshwater inlet valve.

Re-activate warming: Reopen the inlet and outlet valves of the cylinder liner water preheater pump and start the pump, turn on the cylinder liner water heater, and set the control box to "automatic" or manually heating position.

Thermal Monitoring: Stop the main circulation of the cylinder liner water cooler-related systems, the system re-enters the mooring thermal preservation (warming cylinder) state, ⭐ Monitor the temperature not lower than 50°C.

 

III. Summary

Warm-up:

Close the inlet and outlet valves of the warming cylinder water pump, close the warming cylinder water pump, close the electric heating device; Open the hot freshwater inlet valve, open the hot freshwater cooling pump.

Stop/Reduce cooling.

Shutdown:

Close the hot freshwater inlet valve, close the hot freshwater cooling pump; Open the inlet and outlet valves of the warming cylinder water pump, turn on the warming cylinder water pump, heating device.

Stop/Increase cooling.

Send Inquiry