+86-15123173615

Principles and Common Fault Troubleshooting of Cummins Engine PT Fuel System

Sep 27, 2025

Cummins diesel engines compared to other diesel engines. The identification letters PT stand for pressure and time. P refers to the fuel pressure at the inlet of the fuel injector. T indicates the effective time allowed for fuel to flow into the fuel injector cup.

 

info-454-290

 

I. Characteristics of PT Fuel System

The injection pressure range is as high as 10,000 to 20,000 PSI (PSI stands for pounds per square inch, approximately 6.89476 kPa), which can ensure good atomization of the fuel. The maximum fuel pressure output by the PT fuel pump does not exceed 300 PSI.

(2) All the injectors share one fuel supply pipe. Even if some air gets into the fuel system, it won't cause the engine to stall.

(3) The PT fuel pump does not require timing adjustment. The fuel quantity is controlled by the fuel pump and the fuel injector. The engine power can be maintained stably without power loss.

About 80% of the fuel is used to cool the injector and then returns to the fuel tank, ensuring that the injector is well cooled.

(5) It has good versatility. With some adjustments to the same basic pump and injector, it can be applied to different types of engines within a wide range of power and speed variations.

The basic components of the PT fuel system consist of the fuel tank, fuel filter, PT fuel pump, low-pressure fuel delivery pipe, fuel injector, rocker arm, push rod, fuel injection cam and return pipe. Among them, the PT fuel pump includes a gear pump, magnetic filter, pulse diaphragm vibration damper, two-stage governor, throttle shaft and solenoid valve.

The engine fuel system diagram is shown in Figure 1, and the fuel flow schematic diagram is shown in Figure 2.

info-454-344

Figure 1 Engine Fuel System Diagram

 

info-453-366

Figure 2 Schematic Diagram of Engine Fuel Flow

The fuel pump draws fuel from the fuel tank, passes it through the filter and the governor, and delivers it to the fuel injector. According to the design of the PT system, about 80% of the fuel supplied to the fuel injector during operation will return to the fuel tank through the fuel injector, mainly for the purposes of cooling and lubricating the fuel injector, as well as preventing fuel from freezing in cold weather and removing the air in the PT system from the fuel tank.

 

II. Handling Common Faults of the PT Fuel System

(1) Difficulty in starting the engine (unable to start).

If the engine has difficulty starting, fails to start, has insufficient power, cannot stop, or does not shut off, it is generally determined to be a fault of the parking valve.

First, use the manual shaft to open and close the parking valve. Screw the manual shaft in until it cannot be turned any further, which indicates opening.

When parking, unscrew the manual shaft and continue to turn it until it cannot be turned anymore, which indicates closing.

Second, disassemble the parking valve, clean the parts of the parking valve, and use sandpaper to grind the inner hole of the valve body.

(2) Engine runaway (unstable speed).

First, remove the EFC electronic actuator. During the removal process, loosen the installation screws first, then rotate the EFC actuator by 15°, remove the actuator and clean it thoroughly. Then, reinstall it following the steps below: Insert the actuator into the fuel pump body until the actuator flange is about 9.5mm away from the fuel pump body. Then, use your palm to gently push the actuator into the EFC installation hole of the fuel pump, and rotate it by 30° until the actuator flange touches the fuel pump body.

Tighten the installation screws from the bottom in a clockwise direction. First, tighten them by hand until they cannot be tightened any further, then use a wrench to tighten them.

Additionally, check if the diaphragm of the shock absorber is deformed or if there are any hidden cracks.

First, remove the shock absorber, then disassemble it. Check if the diaphragm of the shock absorber is deformed or place the diaphragm onto a hard flat surface. There should be a clear sound. If the sound is dull and muffled, the diaphragm of the shock absorber needs to be replaced.

(3) When the engine with AFC is accelerating, the smoke emission is excessive or the power is insufficient.

The air adjustment screw can be adjusted (only applicable to single-spring AFC, that is, when the air adjustment screw is on the fuel pump body); if the smoke is too much, turn it inwards towards the pump body; if the power is insufficient, turn it outwards. Note: The rotation should be limited to within half a turn.

(4) For the full-flow pump and the power generation pump, if the engine power is insufficient, the throttle of the throttle shaft can be appropriately increased, that is, the forward limit screw can be loosened.

However, for vehicle pumps or pumps where the throttle shaft is not locked at the full throttle position, this throttle cannot be changed.

(5) Idle speed adjustment of the fuel pump.

Since the idle speed adjusted for the fuel pump on the test bench is a fixed value, but the corresponding main engine can vary greatly, the idle speed of the fuel pump can be adjusted.

The idle speed of the two-pole governor is adjusted within the housing of the two-pole spring group, while the VS governor's idle speed is adjusted by the idle speed adjustment screw.

(6) Replace the filter element inside the pre-filter of the parking valve.

When installing the filter element, ensure that the small hole is facing inward and the larger end of the spring is on the outside.

(7) Replace the O-ring and spring of the fuel injector.

During the replacement process, ensure that no dirt enters the inner cavity of the fuel injector.

After replacing the spring, reinstall the fuel injector plunger. Make sure the plunger is clean and free of dirt, and ensure it is inserted smoothly without any obstruction.

Furthermore, the PT fuel system has strict requirements for the cleanliness of the fuel. Most of the faults are mainly caused by poor fuel cleanliness, with excessive impurities (water, wax, dirt) present, which leads to damage of the fuel pump.

Therefore, using high-quality, highly clean fuel, using genuine filter elements and properly maintaining and servicing the system are the prerequisites for the normal operation of the PT system.

Send Inquiry