As the key link in managing a two-stroke diesel engine, cylinder oil is crucial. Here is an introduction to the management knowledge, hoping to offer some help and reminders.
I. Characteristics and Usage Requirements of Cylinder Oil
Marine cylinder oil is mainly used for the lubrication of the cylinder in crosshead diesel engines, including the cylinder liner, piston, and piston rings. The lubrication conditions are extremely harsh. Firstly, under normal operating conditions, the temperature of the cylinder wall near the top dead center can reach 240 to 280°C. If the combustion is poor, the flame may hit the cylinder wall, causing even higher local temperatures. Usually, the temperature of the first piston ring of a water-cooled cylinder liner at the top dead center can reach 180 to 220°C. Secondly, the working conditions of the cylinder determine that a complete oil film cannot be formed on the cylinder wall. The piston is momentarily stationary at the top and bottom dead centers, which will result in boundary lubrication conditions, etc. Therefore, a high-quality marine cylinder oil must have a sufficiently high base number, and the reserve base number must have a rapid acid neutralization capacity. It must also have good detergency and dispersancy, good thermal and oxidation resistance, and good storage stability. In addition, it should have the least amount of abrasive ash. Currently, there is no unified classification standard for cylinder oil grades internationally. They are mostly indicated by the oil's base number and viscosity according to the SAE J183 standard. For example, cylinder oil 5070 means: viscosity grade SAE50, base number 70mgKOH/g, and it is a lubricating oil for the cylinder part of crosshead diesel engines.
II. Principles for Selecting Cylinder Oil
It mainly involves two aspects:
First, viscosity grade. The viscosity grades of cylinder oil are relatively single, with SAE50 being the most common. If the navigation environment temperature is high and the engine condition is slightly poor, it is advisable to choose a slightly higher viscosity grade oil; conversely, a lower viscosity oil can be selected.
Second, quality grade. The quality grade of cylinder oil is distinguished by the size of the total base number (TBN) of the oil. The selection of the oil's base number is very important. It mainly depends on the sulfur content of the fuel used by the ship. Generally speaking, if the TBN is too small, the oil's acid neutralization capacity is insufficient, which can cause corrosion and wear; if the TBN is too large, the metal ash content is high, which can also cause wear. At the same time, due to the large amount of additives, the cost of the oil will increase.
When choosing cylinder oil, the sulfur content of the fuel used should be considered first. When using high-sulfur fuel, high-base number cylinder oil should be selected - this not only neutralizes the acids in the combustion products but also effectively protects the oil film, reduces gas leakage, and keeps the valves and pistons clean. Table U lists the required total base number of cylinder oil for different fuel sulfur contents.

Strictly speaking, when determining the alkaline value of the cylinder oil used, the fuel consumption and lubricating oil consumption of crosshead marine engines should also be taken into account. Under the condition that the sulfur content of the fuel is constant, if the fuel consumption is high, the alkaline value of the cylinder oil should also be high; while if the injection amount of the cylinder oil is large, the alkaline value of the cylinder oil can be smaller. The alkaline value of the cylinder oil can be calculated by the following formula: TBN = 0.35 × S × B/L. In the formula, TBN represents the total base number, mgKOH/g; S represents the sulfur content of the fuel, %; X represents the total coefficient, 0.15 for large marine engines; B represents the fuel consumption per unit time; L represents the cylinder oil consumption per unit time.
When choosing the alkaline value of the cylinder oil based on the sulfur content of the fuel, etc., the boost pressure of the engine should also be considered. For low boost two-stroke engines (P < 7.85 MPa (8 kgf/cm²)), when the sulfur content of the fuel does not exceed 3%, cylinder oil with a TBN of 40 mgKOH/g can be selected. For medium and high boost diesel engines, when the sulfur content is greater than 2%, cylinder oil with a total base number of 50-70 mgKOH/g should be selected.
Whether the alkaline value of the cylinder oil used is sufficient can be determined by intuitive methods. Generally speaking, if a paint-like substance appears on the cylinder surface between the injection points, it indicates that the alkaline value of the cylinder oil is lower than the required value.
III. Management of Cylinder Oil
The cylinder oil injection pump should be carefully managed and refilled in time. When it is found that the oil droplets in the oil pipe are very small or no oil is injected, measures should be taken immediately to eliminate the problem and prevent oil cut-off. At the same time, it is necessary to pay attention to whether there is oil or water leakage at the cylinder oil injection joint to prevent abnormal wear caused by abnormal supply of cylinder oil. The amount of cylinder oil injected should be appropriate. If too much is injected, not only is it wasteful, but the oil will also be blown into the combustion chamber and burned, resulting in an increase in deposits on the top of the piston, ring grooves, ports, and exhaust valves, causing the piston rings and exhaust valves to stick and narrowing the ports and valve channels. At the same time, the cylinder oil will deposit in the scavenging box or exhaust pipe at the bottom of the piston. If the piston leaks, it may cause the scavenging box or exhaust pipe to catch fire. If too little is injected, it is difficult to form a complete oil film, resulting in increased wear of the piston rings and cylinder liner, increased leakage, and the high-temperature exhaust gas leakage will burn the oil film on the cylinder wall, eventually leading to piston ring breakage or seizure. Therefore, diesel engine manufacturers have specified the optimal cylinder oil injection amount for the diesel engines they produce.
The actual oil supply rate depends on the engine model. The table above shows the average oil supply rates for all known models. Generally speaking, the cylinder oil injection amount increases with the increase in the thermal load and power of the diesel engine. Large-bore diesel engines require more injection than small-bore ones. This is because when the power increases, the cylinder temperature also rises, and more cylinder oil volatilizes and burns at high temperatures. Moreover, when the power increases, the acidic combustion residues in the cylinder also increase, so more alkaline cylinder oil is needed to neutralize them. The reason why curved-flow scavenged diesel engines require more injection is mainly because the flow of air and exhaust gas in the cylinder is more chaotic, and some of the cylinder oil is carried into the combustion chamber by the swirling airflow. In addition, the cylinder wall temperature is higher. Generally speaking, the cylinder oil injection amount for medium boost curved-flow scavenged engines is 0.95-1.09 mg/(W·h), while for direct-flow scavenged engines, it is 0.54-0.68 mg/(W·h).