I. Theoretical Analysis of Engine Failure to Start
For the Bosch Common Rail System, the reasons for the engine's failure to start include the following aspects:
1. The vehicle does not supply power to the engine: For electronically controlled engines, the entire working process of the engine is controlled by the central processing unit (ECU). To ensure the engine can start, the prerequisite is to get the ECU working first, and the prerequisite for the ECU to work is to have a normal power supply.
2. The engine fails to quickly build up oil pressure: For the Bosch Common Rail System, the injectors are electronically controlled, but the opening pressure of the injectors also has certain requirements. Only when the oil pressure reaches above 200 bar can the injectors be opened to spray fuel upon receiving the injection command signal from the ECU.
3. Engine phase misalignment: In the Bosch Common Rail System, the injection command is issued by the ECU. However, the ECU only issues the injection command to a certain cylinder when it accurately determines that the cylinder is near the top dead center of compression. If the ECU cannot determine which cylinder has reached the top dead center, it will not issue the injection command, and the injectors will not spray fuel, causing the engine to fail to start. The accurate determination of the engine phase is accomplished by the crankshaft position sensor installed on the pulley and the camshaft signal disc.
4. The engine enters the shutdown protection state: Electronic control engines have the function of self-diagnosis of faults and automatic protection against different levels of faults. When starting, if the ECU detects a fatal fault that could affect the engine, the ECU's protection function will restrict the engine from starting, such as over-temperature protection (water temperature, intake air temperature).
5. Other aspects: Mechanical faults.
II. Troubleshooting Approach
For the fault of an engine not starting, we should follow a step-by-step approach from simple to complex, checking in the order of electrical circuit - fuel circuit - timing - other factors.
1. Electrical Circuit Inspection
First, check if the ECU is receiving power normally. There are three methods to determine this:
a) Turn on the ignition key and supply power to the ECU. If the engine fault light flashes once when the key is turned on and goes out after about 2 seconds, it indicates that the engine ECU has passed its self-check and is working normally. In this case, continue to look for other causes for the engine not starting.
b) Turn on the ignition key and disconnect the water temperature sensor. Use a multimeter to measure the voltage of the sensor. If the sensor has a voltage of around 5V, it indicates that the ECU is working normally. If the voltage is 0V, it means the ECU is not receiving power and is not working.
c) Locate the engine diagnostic connector and measure the voltages of the three wires. If one of the voltages measured to ground is around 24V (battery voltage), another is around 20V, and the third is 0V, it indicates that the engine ECU is working normally. If the 20V voltage is not detected, it means the ECU is not receiving power and is not working.
d) If the ECU is determined not to be working by the above methods, check the power supply circuit of the ECU. For Bosch common rail systems, the power supply to the ECU is as follows: When the ignition key is turned on, it provides an ignition signal to the ECU. This signal line runs from the ignition key to pin 140 of the engine 42-pin connector (refer to the diagram). Disconnect the 42-pin connector, turn on the ignition key, and measure the voltage of pin 140. If there is 24V, it indicates that there is no problem from the ignition key to the 42-pin connector. If there is no 24V, it means there is no power from the ignition key to the 42-pin connector. At this point, check the wiring from the ignition key to the 42-pin connector for any open circuits or short circuits, especially the fuses. Disconnect the 2-pin connector that supplies main power to the ECU and measure the voltage between the two pins with a multimeter. If there is 24V, it is normal. If there is no 24V, it indicates that the main power supply to the ECU from the vehicle is abnormal. Please check the corresponding wiring.
2. Fuel Circuit Inspection
a) Bosch common rail engines are very sensitive to air in the fuel circuit. If there is air in the fuel circuit, it can cause the engine to be difficult to start or not start at all. To remove air from the fuel circuit, loosen the air release bolt at the hand fuel pump seat, press the hand fuel pump to pump fuel until oil comes out of the air release bolt, then tighten the air release bolt and attempt to start the engine.
b) If there is no air in the fuel line, and the engine still cannot start, then use the diagnostic software to check the actual rail pressure establishment during start-up. If the actual rail pressure cannot be established, first loosen the fuel inlet pipe of the fuel transfer pump and pump the hand fuel pump. If there is fuel flowing out from the fuel inlet pipe of the fuel transfer pump, it indicates that the fuel line from the fuel tank to the fuel transfer pump is fine. If no fuel flows out, it indicates that there is a problem with the fuel line from the fuel tank to the fuel transfer pump. Please check the corresponding fuel line. Then, loosen the fuel outlet of the fine filter, start the engine. If there is fuel flowing out from the fuel outlet of the fine filter, it indicates that the fuel line from the fuel transfer pump to the fine filter is fine. If no fuel flows out, it indicates that there is a problem with the fuel line from the fuel transfer pump to the fine filter, usually a fuel transfer pump failure. Loosen the fuel inlet pipe from the high-pressure pump to the common rail pipe, start the engine. If there is fuel flowing out from the fuel inlet pipe, it indicates that the high-pressure pump is supplying fuel normally. If no fuel flows out or only a small amount of fuel flows out, it may be that the fuel supply capacity of the high-pressure pump is poor. Please conduct the corresponding inspection.
3. Inspection of Phases
a) The inspection of phases should be conducted in combination with the diagnostic software. First, read the fault codes through the diagnostic software to see if there are any fault codes related to the camshaft or crankshaft. Next, check the phase data during engine start-up. If the phase is normal, during start-up, in the "Synchronous Phase" item, the phase number will jump between "2", "3", "16", and "48". This is the engine checking the phase relationship. Once the phase is correct, the engine can start smoothly. When the phase is normal, its value should be "48".
b) If the phases are not synchronized, check the crankshaft and camshaft circuits, sensor resistances, and if necessary, swap the crankshaft and camshaft sensors for testing to determine which sensor is faulty and causing the engine to not start or be difficult to start.
c) If there are no issues with the sensors and circuits, then check if the gear box, camshaft signal disc, pulley, etc. are misaligned, shifted, or loose.
4. Other Inspections
Through the diagnostic software, check if there are any fault codes that have triggered engine protection (such as excessively high water temperature). Also, check if the engine operation data is abnormal (such as whether the intake temperature is too high, even reaching over 100 degrees).