+86-15123173615

Analysis and Elimination of Typical Faults of Exhaust Gas Turbochargers: Taking Cummins NTA855 Diesel Engine as an Example (Part Two)

Sep 01, 2025

Ⅲ. Fault Case Analysis and Elimination Measures

When the turbocharger is in operation, there is fresh air and high-temperature and high-pressure exhaust gas inside, and lubricating oil flows inside.

Superchargers have high requirements for neutrality, balance, sealing performance and cleanliness.

These are closely related to crew management and maintenance techniques.

When it is operating normally, the airflow flows rapidly, up to several hundred meters per second.

When it is working normally, the impeller rotates rapidly, reaching several thousand revolutions per second.

Changes in the blades or shaft during use will have an impact on the turbocharger.

 

1. Fault phenomenon

Case:

A certain type of landing boat uses the NTA855-M350 diesel engine as the main engine. This diesel engine is a six-cylinder in-line, forced water-cooled, turbocharged air-cooled and exhaust gas turbocharged four-stroke Marine diesel engine produced by introducing American technology, with a rated power of 261kW and a rated speed of 1800r/min.

This type of diesel engine adopts the ST-50 single-stage radial exhaust gas turbocharger, and the compressor is a single-stage centrifugal compressor.

When the boat was sailing at sea, it was found that the right engine's sliding oil line was leaking oil. After sailing for a period of time, the turbocharger surged at high speed, and then the outer shell turned red.

After shutdown, disassemble the turbocharger and inspect it.
 

2. Elimination process

1) Following the principle of judging first and then inspecting, based on the previously analyzed causes of the diesel engine turbocharger failure and in combination with the fault phenomena, there was an oil dripping phenomenon and the air seal device was damaged. By replacing the oil seal, the oil dripping phenomenon temporarily disappeared.

After sailing for a period of time, the oil dripping phenomenon still occurred.

After replacing the fuel injector, the surge fault still existed.

 

2) Cooling system inspection.

If the water temperature is too high to cool the diesel engine, it will cause the exhaust temperature to be high, and the oil in the turbocharger will evaporate. After long-term operation, oil droplets will adhere to the evaporated oil.

As the intercooler of this type of diesel engine adopts outboard water cooling, the pressure of the cooling system has been checked to be normal.

As the diesel engine can operate normally at all other low speeds, there is a slight blue smoke in the exhaust. The exhaust temperatures of each cylinder do not differ much. The problem with the cooling system is ruled out, and the fault is analyzed to be caused by the intake and exhaust system or the fuel system.

 

3) Inspection of intake and exhaust valves.

If the valve clearance is inappropriate and the intake and exhaust valves do not close tightly, it will cause severe carbon deposits or erosion on the intake and exhaust valves, thereby leading to surging of the turbocharger.

After berthing at the wharf, the sealing conditions of the intake and exhaust valves of each cylinder were inspected. It was found that the valve stems and the bases of the intake and exhaust valves were sealed normally, with no severe carbon deposits or erosion. The valve clearances of each cylinder were normal.

The intake and exhaust valves of each cylinder, the fuel system and the high-pressure oil pump were inspected. After the high-pressure oil pumps of each cylinder were calibrated and the fuel supply timing was adjusted, the surge fault disappeared, but the oil dripping phenomenon still existed.

 

4) Checking the instrument found that the pressure gauge was abnormal.

When the intake and exhaust, as well as the negative pressure in the crankcase, are unbalanced, the pressure seal fails, and the lubricating oil is sucked into the compressor. After being pressurized with the air, it enters the cylinder.

The intake system affects the performance of the diesel engine, causing oil leakage from the turbocharger.

Disassemble the air inlet and outlet pipes of the turbocharger. The pipe walls are covered with oil stains.

Considering the wear caused by the fit clearance between the cylinder liner and the piston ring, the piston ring was replaced and the oil leakage phenomenon disappeared.

 

5) Adjust the dynamic balance of the turbocharger rotor. When the turbocharger operates at a very high speed, the rotor will experience unbalanced inertial forces, which will have an adverse effect on it.

Not only will it make the wear more severe, but it will also increase the weight that the bearing bears.

Therefore, after the supercharger is removed or replaced and the installation is completed, a dynamic and static balance test should be conducted on it to control the unbalance degree within the required range.

The static balance test can be conducted by rotating any Angle and making a mark. If the mark does not move after releasing the hand, the test is considered static. If the mark changes Angle, then slightly file the heavier side with a file to reduce the weight.

Dynamic balancing requires calculation to eliminate the unbalance.

Then keep trying until the requirements are met.

 

3. Cause analysis

The oil dripping phenomenon in this case reflects the loopholes in maintenance.

The daily management of exhaust gas turbochargers mainly involves observing the flow of lubricating oil and paying attention to whether the pressure and temperature of the lubricating oil are abnormal.

When the turbocharger is in operation, the lubricating oil pressure should not be too high to prevent the lubricating oil from being squeezed into the turbine chamber.

At this point, the consumption rate of lubricating oil increases, and there is a high possibility of a runaway.

Adjust the lubricating oil cooler to keep the lubricating oil temperature within an appropriate range to prevent the rotating shaft and bearings from overheating due to insufficient cooling during the operation of the turbocharger.

In addition, if a single cylinder of the high-pressure oil pump does not supply oil or the oil supply is uneven, the load on each cylinder of the main unit will be different, causing the turbocharger to surge.

At the same time, inaccurate fuel supply timing led to afterburning. The exhaust pipe contained incompletely burned fuel, which entered the turbocharger, causing the turbocharger to overheat and turn red.

 

Ⅳ. Management Insights and Suggestions

When diesel engines run for a long time or are overloaded, malfunctions are inevitable. To prevent such malfunctions, maintenance and upkeep are necessary.

Before shutting down, it should idle for 3 to 5 minutes and the smoothness of its operation should be checked.

If the sound is abnormal, the machine should be stopped for inspection.

Frequently check the airtightness of the airways and regularly inspect the turbocharger.

After running for a period of time, the interior of the turbocharger will rust and impurities will appear, and the performance of the bearings will also change due to temperature rise.

It should be cleaned regularly in accordance with the vessel maintenance regulations to prevent inhalable particles from blocking the compressor, so as to ensure that it is in good working condition.

Use acid solution to remove rust and diesel to clean the filter.

Prepare or purchase a hydrochloric acid solution with a concentration of 10% to 15% or a sulfuric acid solution with a concentration of 15% to 20% to clean the scale. Then neutralize the residual acid with alkaline water, wash the chemical reagents with clean water, and finally blow and dry with compressed air.

 

When disassembling and assembling the turbocharger, one should refer to the manufacturer's provided manual or user manual to understand the internal structure and be familiar with the disassembly and assembly procedures before proceeding with the disassembly and assembly.

When the turbocharger is damaged during operation and cannot be repaired by replacing parts on board, the operation should be immediately stopped and measures taken to prevent other damages to the turbocharger.

If the rotor stops rotating, to prevent fire, the supply of lubricating oil to the faulty turbocharger must be forcibly cut off, and at the same time, the output power of the diesel engine should be reduced to ensure that the exhaust temperature does not exceed the specified value.

If the exhaust gas must be conveyed through the turbocharger, the rotor sleeve of the faulty turbocharger should be removed and the sealing cover should be put on. Otherwise, the entire faulty turbocharger should be removed and the relevant pipelines should be sealed or reconnected.

When maintaining and servicing, minor malfunctions should be repaired by the users.

Inspections, repairs or major malfunctions that exceed the scope of maintenance and servicing should be sent to a repair shop or the manufacturer.

When the rotor and bearings are damaged, to restore the operation of the diesel engine, a spare rotor assembly can be replaced.

 

info-400-400

 

V. Conclusion

Supercharging technology is advancing rapidly, and its structure and functions have also been optimized along with the development of diesel engines.

The long-standing problems with turbochargers directly affect the service life of diesel engines and navigation safety.

The rational use of turbochargers and regular maintenance are effective measures to solve turbocharger faults.

When a turbocharger malfunctions, it should be inspected step by step based on the cause of the fault phenomenon to improve the efficiency of fault diagnosis and elimination. The research on other faults such as shutdown, gas channel corrosion, turbine oil leakage and abnormal noise needs to be carefully observed and analyzed in daily use and management.

 

The shipbuilding department is in a stage of transformation and development, and higher requirements have also been put forward in the management and use of machinery.

The widely used exhaust gas turbochargers at present can greatly improve efficiency and reduce fuel consumption.

However, exhaust gas turbochargers often encounter a series of faults. By analyzing the typical faults of turbochargers through fault examples, and combining the usage of Marine diesel engines and relevant operation and management regulations, effective methods can be summarized and explored, which is bound to provide a reference for better performing the support tasks.

Send Inquiry