The automobile generator is the main power supply of the automobile, its function is to supply power to all electrical equipment (except the starter) when the engine is running normally, and charge the battery at the same time.
On the basis of the common alternator three-phase stator winding, increase the number of winding turns and lead out the terminal, add a set of three-phase bridge rectifier. At low speed, the primary winding and the extension winding are output in series, and at high speed, only the primary three-phase winding is output.
Working principle
The working principle of the whole alternator
When the external circuit energizes the field winding through the brush, a magnetic field is generated, so that the claw pole is magnetized into the N pole and the S pole. When the rotor rotates, the magnetic flux alternately changes in the stator winding, according to the principle of electromagnetic induction, the stator three-phase winding will produce alternating induced electromotive force. This is how an alternator generates electricity.
The prime mover (i.e. the engine) drags the DC excited synchronous generator rotor to rotate at the speed n(rpm), and the three-phase stator winding induction AC potential. If the stator winding is connected to the electrical load, the motor has AC power output, and the AC power is converted into direct current from the output terminal through the rectifier bridge inside the generator.
Alternator is divided into two parts of stator winding and rotor winding, three-phase stator winding is distributed on the shell according to the electric Angle of 120 degrees difference between each other, rotor winding is composed of two pole claws. When the rotor winding is connected to direct current, it is excited, and the two pole claws form the N pole and the S pole. The magnetic field line starts from the N pole, enters the stator core through the air gap and returns to the adjacent S pole. Once the rotor is rotated, the rotor winding will cut the magnetic force line, and generate sinusoidal electromotive force with a difference of 120 degrees electrical Angle in the stator winding, that is, three-phase alternating current, and then through the rectifier element composed of diodes into direct current output.
When the switch is closed, the battery first provides current. The circuit is:
Battery positive → charging light → regulator contact → excitation winding → lap iron → battery negative. At this time, the charging indicator light will light up due to the current passing through.
However, after the engine starts, as the generator speed increases, the generator terminal voltage also increases. When the output voltage of the generator is equal to the battery voltage, the potential of the "B" end and "D" end of the generator is equal, at this time, the charging indicator light is extinguished because the potential difference between the two ends is zero. Indicates that the generator is working normally and the excitation current is supplied by the generator itself. The three-phase AC electromotive force generated by the three-phase winding in the generator is rectified by the diode and outputs direct current to supply power to the load and charge the battery.
Structural principle
The conversion of high and low speed power supply circuit is automatic, and no electromechanical control device is added. The working principle is analyzed as follows:
In the low speed range, due to the low speed of the generator, the series output of the three-phase winding improves the output voltage of the generator, and the low-speed charging performance of the generator is greatly improved. In the high speed range, with the increase of the generator speed, the inductive reactance of the seried-connected three-phase winding increases, the internal pressure drop increases, and the armature reaction is strengthened, so that the output voltage drops. At this time, the original three-phase winding A, B, C because of the small internal pressure drop, the induced current generated is relatively large, to ensure the power output at high speed.
Dynamic property
In the process of car trading, we must carry out road tests, however, in the process of road testing must take into account the power of the vehicle, then, what is the power of the car?
The power of the car refers to the process of the car driving in a straight line on a good road surface, and the corresponding driving performance can be determined by the longitudinal external force, which is able to meet the requirements of the average driving speed. From this definition, we can see that for a road, it must be a good road surface, level or slope can be used, the mode of movement can take a straight line driving process, for external factors, the longitudinal external force can determine the basis of the movement, so that it can reach a certain capacity. For athletic ability, there are three main indicators, such as the car's maximum speed, acceleration time, and maximum climb. A vehicle driving on a good level road surface, if it can reach the highest speed, we call it the maximum speed. For acceleration time, it is usually the acceleration time of starting in place, and the acceleration time of overtaking, which indicates the acceleration ability of the car. "t" indicates the time to start in place, which is generally first or second gear to start, and gradually change gears, if you travel to a certain predetermined distance, the time required for the speed. It's time to start in place. The acceleration time of overtaking can also be expressed by "t", and some of the highest second-high gear cars, their speed is about 30 or 4, and the time taken to accelerate at full speed on some expressways is expressed.
Matters needing attention
Alternators are widely used in cars, and the following points should be noted when using them:
① Often clean the dirt and dust on the surface of the generator, keep it clean and well ventilated.
② Often check the fastening of the fasteners related to the generator, and tighten the screws in time.
③ The tension of the transmission belt should be appropriate. Too loose, easy to slip and cause insufficient power generation; Too tight, easy to damage the belt and generator bearings.
④ When installing the battery, do not install the wrong, usually install the positive wire first, do not install the wire, otherwise it is easy to burn the diode.
When the integrated circuit regulator is used, the ignition switch should be turned off immediately when the engine is not running.
It is not allowed to use the "scraping fire" method to test whether power generation.
When the generator has a fault and does not generate power, it should be eliminated in time, otherwise it will cause more serious faults.
Dynamo
Electric energy is one of the most important energy sources in modern society. Generator is a mechanical equipment that converts other forms of energy into electrical energy. It was first produced during the second Industrial Revolution and made by German engineer Siemens in 1866. Driven by water turbine, steam turbine, diesel engine or other power machinery, it converts the energy generated by water flow, air flow, fuel combustion or nuclear fission into mechanical energy to the generator. It is then converted into electricity by a generator. Generators are widely used in industrial and agricultural production, national defense, science and technology and daily life
There are usually three categories of generators:
1. Classified by the mode of electrical energy conversion
According to the conversion of electrical energy can be divided into alternator and DC generator two categories.
Alternator is divided into synchronous generator and asynchronous generator two kinds. Synchronous generators are divided into hidden pole synchronous generators and salient pole synchronous generators. Synchronous generators are most commonly used in modern power stations, and asynchronous generators are rarely used.
Ac generator sets can be divided into two types: single-phase generator and three-phase generator. Three-phase generator output voltage is 380V, single-phase generator output voltage is 220V.
2. Classification by excitation mode
According to the excitation mode can be divided into brush excitation generator and brushless excitation generator two categories
The excitation mode of the brushless excitation generator is separately excited, and the excitation mode of the brushless excitation generator is self-excited. The rectifier of the separately excited generator is on the generator stator, and the rectifier of the self-excited generator is on the rotor of the generator set.
3. Classification by driving power
There are many forms of generator drive power, common power engines are:
(1) Wind turbine
Wind turbine is to rely on the wind to drive the generator rotation, generate current; This kind of generator does not need to consume additional energy, is a pollution-free generator;
(2) Hydraulic generator
Hydraulic generator is the use of water flow drop, generate power, drive the generator to generate electricity, but also the use of green natural resources to generate electricity equipment, also known as hydrogenerator
(3) Fuel generator
Oil-fired generators rely on diesel or gasoline combustion to generate power to drive the generator set. The use of small oil-fired generators can play an emergency role. In case of power failure, the fuel generator can be started to generate electricity to maintain normal operation