+86-15123173615

Case Analysis and Troubleshooting of STC Turbocharger Fault in PA6 Diesel Engine Part 1

Jan 11, 2025

I. Composition and Principle of STC Supercharging System
Sequential TurboCharging (STC) technology is an advanced turbocharging technique that integrates two or more turbochargers to operate in parallel. As the load and speed of the diesel engine increase, these turbochargers are sequentially activated based on predefined operating conditions [1]. This technology specifically addresses the matching and performance challenges between traditional diesel engines and turbochargers, aiming to significantly enhance the engine's efficiency and economy under low-speed, high-load conditions while optimizing overall power output and emission performance.

1. Composition of STC Supercharging System
STC is an energy-efficient and high-performance supercharging technology primarily used in diesel engines for large ships, heavy vehicles, and industrial applications.
The PA6 propulsion diesel engine employs this technology, comprising an STC control system and two parallel first-stage exhaust gas turbochargers for step-by-step supercharging.
Among the two exhaust gas turbochargers of the PA6-STC diesel engine:
- The one directly connected to the exhaust manifold of column A serves as the primary turbocharger, referred to as the A-column turbocharger.
- The one connected to the exhaust manifold of column B acts as the controlled turbocharger, known as the B-column turbocharger.
During diesel engine operation, the exhaust gases drive either one or both of the first-stage exhaust gas turbochargers, which compress the intake air, increasing the intake pressure and temperature. This process enhances the combustion efficiency and improves the diesel engine's power and efficiency.
The STC control system consists of four pneumatic butterfly valves, an STC controller, and a butterfly valve detection solenoid valve box. It continuously monitors critical parameters such as diesel engine speed, load, and exhaust temperature. Based on these parameters, the system controls the operation of the turbochargers. Specifically:
- The gas valve is installed at the turbine inlet of the B-column turbocharger.
- The air valve is installed at the compressor outlet of the B-column turbocharger.
- The bypass valve (to prevent turbocharger surge) is installed between the compressor outlet and the turbine inlet.
- The blow-off valve (to prevent excessive cylinder pressure in low-temperature environments) is installed in the intake system before the engine.
The STC controller is the core component of the control system, responsible for collecting data on turbocharger speed, boost pressure, diesel engine speed, fuel rack position, and fuel rack zero position [2]. It controls the opening and closing of the four butterfly valves, enabling the B-column turbocharger to be engaged or disengaged as needed, thereby meeting the performance requirements of the diesel engine under varying load conditions.
2. Working Principle of Exhaust Gas Turbocharger
The exhaust gas turbocharger of the PA6-STC diesel engine primarily comprises a centrifugal compressor and an exhaust gas turbine, as illustrated in the cross-sectional view of the exhaust gas turbocharger (Figure 1). These components are mounted on the same main shaft and function as a high-speed rotating machine, capable of reaching rotational speeds of tens of thousands of revolutions per minute or higher.

 

info-591-404

 

 

The working principle of the STC supercharging system involves the high-temperature, high-speed exhaust gas discharged from the diesel engine cylinders entering the non-water-cooled turbine inlet housing via the nozzle ring to expand. This expansion converts thermal energy into mechanical energy, driving the turbine to rotate and, in turn, rotating the coaxial compressor impeller. The exhaust gas is then cooled by the water-cooled turbine outlet housing before being discharged into the atmosphere.
The compressor draws in fresh air through the intake system and compresses it. The compressed, high-speed air passes through the diffuser for further pressurization and then flows through the intercooler for cooling and de-pressurization. Finally, the cooled air enters the diesel engine intake manifold and is supplied to the cylinders, achieving the purpose of supercharging. This process allows the diesel engine to intake more air and burn more fuel, thereby enhancing power output and thermal efficiency.
3. Basic Principle of the STC Control System
The STC supercharging system operates in two primary modes: 1TC (single turbocharger) and 2TC (dual turbochargers), as illustrated in Figure 2, the schematic diagram of the STC supercharging system.

 

info-612-525

 

 

When the diesel engine operates at low load, the gas valve and air valve are closed. In this state, only the A-column turbocharger is active, while the B-column turbocharger is isolated by the closed valves and remains inactive. This configuration is referred to as the 1TC (single turbocharger) working mode [3-4]. During this mode, the exhaust gas from both A-column and B-column cylinders is sufficient to meet the operational requirements of the A-column turbocharger, ensuring optimal performance of the main engine under low-load conditions. This enhances the power output and fuel efficiency of the propulsion diesel engine at low loads, while also reducing exhaust temperature and fuel consumption rate.
When the engine reaches high-load conditions, the gas valve and air valve open, allowing the previously idle B-column controlled turbocharger to engage in parallel with the A-column turbocharger. This results in both A-column and B-column turbochargers operating simultaneously in parallel, which is designated as the 2TC (dual turbocharger) working mode. As the load and speed of the diesel engine increase from low to high and reach a predetermined threshold, the system transitions from the 1TC to the 2TC mode. Conversely, when the load and speed decrease, the system switches back from 2TC to 1TC mode. The bypass valve and blow-off valve are activated during specific operating conditions of the diesel engine or during the transition between 1TC and 2TC modes.

 

Send Inquiry