+86-15123173615

marine diesel

Oct 14, 2024

Marine diesel engines have high thermal efficiency, good economy, easy starting, and great adaptability to various types of ships. After their introduction, they were quickly used as propulsion power for ships. By the 1950s, diesel engines had almost completely replaced steam engines in newly constructed ships. Marine diesel engines have become the main power source for civilian ships, small and medium-sized vessels, and conventional submarines. Marine diesel engines can be divided into main engines and auxiliary engines according to their functions in ships. The main engine is used as the propulsion power for ships, while the auxiliary engine is used to drive generators, air compressors, or water pumps.

 

Marine diesel engines are generally divided into high-speed, medium speed, and low-speed diesel engines, and the main performance indicators of the three types of diesel engines are listed in the table.

 

Introduction and Application

Most of the time, marine engines work at full load, and sometimes operate under variable load conditions. Ships often navigate in rough terrain, so marine diesel engines should be able to operate reliably under conditions of longitudinal inclination of 15 ° -25 ° and transverse inclination of 15 ° -35 °. Most ships use turbocharged diesel engines (see internal combustion engine turbocharging), and low-power non turbocharged diesel engines are only used in small boats. Most low-speed diesel engines are two-stroke engines, most medium speed diesel engines are four stroke engines, and high-speed diesel engines have both. The scavenging forms of marine two-stroke diesel engines include reflux scavenging, port valve DC scavenging, and opposed piston port scavenging. High power medium and low-speed diesel engines widely use heavy oil as fuel, while high-speed diesel engines still mostly use light diesel.

 

low-speed diesel engine

Directly driving the propeller requires a lower rotational speed in order to achieve high propulsion efficiency. Medium and high-speed diesel engines drive the propeller through a gearbox, which is usually equipped with a reversing mechanism to achieve propeller reversal. However, low-speed diesel engines and some medium speed diesel engines can reverse themselves. Medium and high-speed diesel engines are also electrically driven through a generator motor propeller system. When high power is required, multiple machines can also be used in parallel, and only one main engine can be used for low-speed navigation, thereby improving operational efficiency and reliability. When installing two main engines on the same ship, they are divided into left engine and right engine according to the installation position and propeller direction.

 

Working principle

two-stroke diesel engine

A diesel engine that completes one working cycle through two strokes of the piston is called a two-stroke diesel engine. An oil engine completes one working cycle with only one revolution of the crankshaft. Compared with a four stroke diesel engine, it improves the power output and has significant differences in specific structure and working principles.

 

The basic structure of a two-stroke diesel engine is the same as that of a four stroke diesel engine, with the main difference being in the valve train. Two stroke diesel engines do not have intake valves, and some do not even have exhaust valves. Instead, scavenging and exhaust ports are provided at the lower part of the cylinder; Or set up a scavenging port and exhaust valve mechanism. And a dedicated scavenging pump driven by moving parts and a scavenging box for storing pressure air are set up, which simplifies the structure of the diesel engine by using the coordination between the piston and the air port to complete the air distribution. The diagram shows the working principle of a two-stroke diesel engine. The scavenging pump is attached to one side of the diesel engine, and its rotor is driven by the diesel engine. Air is sucked in from the pump, compressed and discharged, and stored in a large volume scavenging box, where it maintains a certain pressure.

 

4-stroke diesel engine

The work of a diesel engine is completed by four processes: intake, compression, power generation, and exhaust, which form a working cycle. A diesel engine in which the piston completes a working cycle through four processes is called a four stroke diesel engine. Now compare it with the animation above to explain its working principle.

 

The first stroke - suction, its task is to fill the cylinder with fresh air. When the suction stroke begins, the piston is at top dead center, and there is still some exhaust gas left in the combustion chamber of the cylinder.

 

When the crankshaft rotates elbow, the connecting rod moves the piston from top dead center to bottom dead center, and at the same time, uses the transmission mechanism connected to the crankshaft to open the intake valve.

 

As the piston moves downwards, the volume above the piston in the cylinder gradually increases: causing the air pressure inside the cylinder to be lower than the pressure inside the intake pipe, so the outside air continuously fills the cylinder.

 

The variation of gas pressure in the cylinder with the volume of the cylinder during the intake process is shown in the animation. The vertical axis in the figure represents the gas pressure P, and the horizontal axis represents the cylinder volume Vh (or piston impulse S). This graph is called an indicator diagram. The pressure curve in the figure represents the variation law of gas pressure inside the cylinder when the diesel engine is working. We can see from the soil that the intake begins, and due to the presence of residual exhaust gas, it is slightly higher than the atmospheric pressure P0. During the intake process, due to the flow resistance generated by the air passing through the intake pipe and intake valve, the gas pressure during the intake stroke is lower than atmospheric pressure, ranging from 0.085 to 0.095 MPa. Throughout the entire intake process, the gas pressure inside the cylinder remains roughly constant.

 

When the piston moves downward and approaches the bottom dead center, the airflow entering the cylinder still has a high velocity and a large inertia. In order to use the inertia of the airflow to increase the inflation rate, the intake valve closes only after the piston has passed the bottom dead center. Although the piston is moving upwards at this time, due to the inertia of the airflow, the gas can still fill the cylinder.

 

Second stroke - compression. During compression, the piston moves from bottom dead center to top dead center. This stroke has two functions: firstly, to increase the temperature of the air and prepare for the self ignition of the fuel; secondly, to create conditions for gas expansion and work. When the piston moves upward and the intake valve closes, the air in the cylinder is compressed. As the volume decreases, the pressure and temperature of the air continue to rise. The pressure and humidity at the end of compression are related to the degree of compression of the air, that is, to the compression ratio. Generally, the pressure and temperature at the end of compression are Pc=4-8MPa, Tc=750-950K.

 

The self ignition temperature of diesel is about 543-563K, and the temperature at the end of compression is much higher than the self ignition temperature of diesel, which is sufficient to ensure that the fuel injected into the cylinder ignites and burns on its own.

 

The diesel injected into the cylinder does not ignite immediately, and it only ignites after undergoing physical and chemical changes. This period of time is approximately 0.001-0.005 seconds, known as the ignition delay period. Therefore, it is necessary to start spraying atomized fuel into the cylinder at a crank angle of 10-35 ° before the crankshaft reaches the top dead center, and to achieve the highest combustion pressure in the combustion chamber when the crankshaft reaches 5-10 ° after the top dead center, forcing the piston to move downward.

 

Third stroke - doing work. At the beginning of this stroke, most of the fuel injected into the combustion chamber is burned. During combustion, a large amount of heat is released, causing a sharp increase in gas pressure and temperature. The piston moves downward under the action of high-temperature and high-pressure gas, and rotates the crankshaft through the connecting rod to perform external work. So this stroke is also called the power or working stroke.

 

As the piston descends, the volume of the cylinder increases and the pressure of the gas decreases. The working stroke ends when the piston reaches the bottom dead center and the exhaust valve opens.

 

In the animation, the rising part of the pressure change line during the working stroke represents the sharp increase in pressure when fuel is burned in the cylinder, and the highest point represents the highest combustion pressure Pz. The pressure and temperature at this point are:

Pz=6~15MPa, Tz=1800~2200K

 

The ratio of the highest combustion pressure to the compression endpoint pressure (Pz/Pc) is called the pressure rise ratio during combustion, expressed as λ. According to the different types of diesel engines, the range of λ value at maximum power is as follows: λ=Pz/Pc=1.2-2.5.

 

Fourth stroke - exhaust. The function of the exhaust stroke is to discharge the expanded exhaust gas to fill with fresh air and prepare for the intake of the next cycle. When the working stroke piston moves to near the bottom dead center, the exhaust valve opens, and the piston moves from the bottom dead center to the top dead center under the drive of the crankshaft and connecting rod, and discharges the exhaust gas out of the cylinder. Due to the resistance in the exhaust system, at the beginning of the exhaust stroke, the gas pressure inside the cylinder is 0.025-0.035MPa higher than atmospheric pressure, with a temperature Tb of 1000-1200K. In order to reduce the resistance of piston movement during exhaust, the exhaust valve is opened before the bottom dead center. As soon as the exhaust valve is opened, gas with a certain pressure immediately rushes out of the cylinder, and the pressure inside the cylinder rapidly drops. This way, when the piston moves upward, the exhaust gas inside the cylinder is discharged through the upward movement of the piston. In order to utilize the inertia of the airflow during exhaust to ensure that the exhaust gas is discharged cleanly, the exhaust valve is closed only after the top dead center.

 

In the animation, the exhaust stroke curve represents that the gas pressure inside the cylinder is almost constant during the exhaust process, but slightly higher than atmospheric pressure. The pressure Pr at the end of the exhaust stroke is approximately 0.105-0.115MPa, and the temperature Pr of the residual exhaust gas is approximately 850-960K.

 

Due to the fact that the intake and exhaust valves are opened early and closed late; So at the end of the exhaust stroke and the beginning of the intake stroke, when the piston is near the top dead center, there is a period of time when the intake and exhaust valves open simultaneously, which is represented by the crankshaft angle and called the valve overlap angle.

 

After the exhaust stroke ends, the intake stroke begins again, and the entire working cycle is repeated according to the above process. Due to the fact that the working cycle of this diesel engine is completed by four piston strokes, i.e. two revolutions of the crankshaft rotation, it is called a four stroke diesel engine.

 

In the four strokes of a four stroke diesel engine, only the third stroke, which is the working impulse, generates power to perform external work, while the other three strokes are the preparation process for consuming work. To achieve this, a flywheel must be installed on a single cylinder diesel engine, utilizing the rotational inertia of the flywheel to ensure continuous and uniform operation of the crankshaft throughout the four strokes.

 

Structural advantages

1. Unique frame type main bearing structure, high body stiffness, small vibration amplitude, and low noise decibels.

2. One cylinder, one cover, facilitates vehicle maintenance and reduces maintenance costs.

3. The main components are constantly purchased globally, achieving high engine configuration.

4. The diesel engine accessories are fully installed, with air coolers, seawater and fresh water heat exchangers, etc. installed on the diesel engine for easy layout of the engine compartment.

5. The cooling system of the diesel engine adopts an internal and external dual circulation water cooling method. The internal circulation uses fresh water to cool the diesel engine, while the external circulation uses seawater to cool the fresh water through a sea fresh water heat exchanger, which improves the service life of the diesel engine.

6. A comprehensive protection and control system, equipped with a diesel engine functional monitoring instrument, can automatically measure and display the speed, water temperature, oil temperature, and pressure of the diesel engine. When the diesel engine parameters exceed the limit, it can automatically alarm and shut down, and a remote control instrument can be optionally equipped.

7. Excellent design, using a water jacket exhaust pipe to maintain low cabin temperature.

8. It has good adaptability and is compatible with WD615C and WD618C series diesel engine flywheels, flywheel housings, diesel engine monitoring instruments, water jacket exhaust pipes, seawater pumps and other components. The installation dimensions of the diesel engine, flywheel, and flywheel housing are also the same, which facilitates matching and maintenance.

9. The front end pulley of the crankshaft is reserved with a pulley groove and a connecting flange for outdoor power output devices.

 

info-416-314

 

 

Send Inquiry