+86-15123173615

Analysis and Countermeasures for High Temperature Faults of QSK60 Engine

Feb 18, 2025

info-600-375

Analysis of High Temperature Faults in QSK60 Engine

I. Internal Factor Analysis
The internal factors leading to high-temperature faults in the QSK60 engine can be categorized as follows:

1. **Water Pump Malfunction**
- A malfunctioning water pump results in insufficient flow pressure for the antifreeze, causing it to flow too slowly and fail to effectively carry heat away from the engine.

2. **Radiator Design and Maintenance Issues**
- Poor radiator design or structural defects, along with excessive accumulation of oil and dust on its surface, significantly impede heat dissipation, leading to inadequate cooling performance. This ultimately causes the engine temperature to rise excessively.

3. **Fan and Clutch Failure**
- Faulty fan blades or clutch mechanisms reduce the airflow required for cooling, affecting the rapid decrease in antifreeze temperature and diminishing the overall cooling effect on the engine, resulting in overheating.

4. **Thermostat Blockage or Malfunction**
- A clogged or improperly functioning thermostat prevents the antifreeze from reaching the necessary large circulation opening temperature, hindering timely cooling and leading to elevated antifreeze temperatures, which cannot effectively cool the engine.

5. **Insufficient Antifreeze Level or Concentration**
- Low antifreeze levels or inadequate concentration of effective components hinder the removal of heat generated by the engine, gradually increasing the engine temperature.

6. **Other Adverse Factors**
- Clogged air filters reduce intake pressure, while damaged fuel injectors cause incomplete combustion, leading to higher exhaust gas temperatures. These conditions reduce the cooling efficiency of the antifreeze and prevent timely cooling of the engine, ultimately causing overheating.

II. External Factor Analysis
1. **Ambient Temperature Influence**
- The engine's temperature is influenced by ambient conditions. Higher ambient temperatures reduce the temperature differential between the antifreeze and the surrounding atmosphere, significantly diminishing the cooling effect. Since ambient temperature is uncontrollable, preparations must be made to ensure safe engine operation through proper accessory readiness and personnel arrangements.

2. **Overloading**
- Continuous overloading generates excessive heat that exceeds the cooling system's capacity, leading to heat accumulation within the engine and eventual high-temperature malfunctions.

III. Measures for Eliminating High-Temperature Faults
1. Troubleshooting and Elimination of Thermostat Faults
- The thermostat regulates the amount of antifreeze entering the radiator based on its temperature, adjusting the circulation mode and heat dissipation capacity to maintain optimal engine temperature.
- The QSK60 engine typically uses a wax thermostat with a temperature regulation range of 82 to 90°C.
- After starting the engine, if the antifreeze level in the radiator remains calm when the water filling port cover is opened, the thermostat is functioning normally. Otherwise, it indicates a malfunction.
- If the antifreeze temperature initially rises rapidly but slows down after reaching 86°C, the thermostat is working correctly. Conversely, if the temperature continues to rise rapidly and suddenly overflows, it suggests the main valve is stuck and requires immediate attention.

2. Inspection and Troubleshooting of Antifreeze and Temperature Sensor
- Properly prepared antifreeze efficiently transfers heat from the engine to the atmosphere. The antifreeze used in the QSK60 engine is a mixture of ethylene glycol and pure water, containing DCA4 additives.
- The recommended ratio of antifreeze to pure water is between 40% and 68%, ideally around 50%. Additionally, 0.5 units of DCA4 should be added per liter of antifreeze.
- For testing the temperature sensor, place it in water at 30, 50, 80, and 100°C. If the temperature difference does not exceed ±3°C, the sensor is qualified; otherwise, it should be replaced promptly.

3. Fault Inspection and Elimination of Fan Drive Belt
- The fan, located behind the radiator, is driven by a V-belt connected to the pulley at the front end of the crankshaft. Proper fan rotation draws air through the radiator, effectively lowering the antifreeze temperature.
- Insufficient fan speed reduces the air volume passing through the radiator, decreasing heat dissipation and leading to overheating.
- The fan's speed is controlled by the drive belt tension. Insufficient tension can cause slippage during high-speed operation, reducing fan speed and causing severe wear on the belt.
- Ensure the drive belt tension is appropriate, with a deflection of 5 to 10mm when applying a force of 40 to 50N with the thumb.

4. Fault Inspection and Elimination of Water Pumps
- Hold the radiator outlet pipe tightly and gradually increase engine speed from idle to high. If the water flow rate increases gradually, the water pump is functioning normally. Otherwise, inspect and repair or replace the water pump.
- When the engine temperature is high, check for changes in antifreeze color, oil contamination, and abnormal engine sounds. These signs indicate potential cylinder penetration or cracks in the water pump, requiring prompt replacement.

5. Fault Inspection and Elimination of Radiator
- In harsh working environments, dust and dirt accumulate on the radiator fins, impeding heat dissipation.
- Touch the radiator fins to feel the temperature difference between the upper and lower parts. A significant temperature difference indicates blocked fins.
- Unclog the fins to improve heat dissipation and prevent deformation from external forces. Ensure the quality of the antifreeze added to achieve optimal cooling performance.

IV. Conclusion
In summary, numerous factors contribute to high-temperature faults in the QSK60 engine. To quickly identify and resolve these issues, a systematic and comprehensive analysis of the engine's operating conditions is essential to accurately determine the fault's root cause. This article provides an in-depth analysis of the causes of high-temperature faults in QSK engines and proposes targeted troubleshooting measures, enabling rapid fault resolution and ensuring reliable engine operation.

 

info-600-375

 

Send Inquiry