+86-15123173615

Full Analysis of Fault Lights for National VI Engines

Jan 25, 2026

1. Yellow Warning Light
 

info-85-79

 

The fault already exists but the vehicle can still continue to run. However, the driver should report for repair as soon as possible to avoid the fault from worsening.

 

2. Red stop indicator light

 

info-85-68

 

When it remains on, it indicates that there is a serious fault with the engine. Please stop the vehicle as soon as possible. When it keeps flashing, the engine will automatically stop in 30 seconds.

Press the "override switch" indicated by the green arrow to force the vehicle to continue running for 30 seconds to ensure a safe stop.

 

3. Waiting for start indicator light
 

info-95-77


When it remains lit, it indicates that the intake air is preheating. The engine should be started after it goes out. When it keeps flashing, it indicates that the start-up has timed out. The motor should be paused for 2 minutes and then restarted.


4. MIL Indicator Light - Abnormal Function Indicator Light

 

info-95-79

 

The MIL light is used to indicate faults related to post-treatment. According to the national VI regulations, there is a 5-second self-check process for the MIL light when the vehicle is powered on at T15. During the actual vehicle matching process, since the initialization time of the instrument panel is much longer than that of the ECU, it is difficult to observe the 5-second constant-on process of the MIL light on the actual vehicle instrument panel.

info-850-323

 

Under normal circumstances, when the vehicle is powered on but not started, the instrument self-check takes about 30 seconds. If the engine has no faults, the MIL light will flash once periodically and then go off immediately after starting. If it flashes twice, it indicates a Class C fault and will go off immediately after starting. If it flashes three times, it indicates a Class B fault and the OBD light will go off after 15 seconds. If the OBD light remains on constantly, it indicates a Class A fault and will remain on constantly after starting. When Class A, B, or C faults are indicated, please contact the service station as soon as possible for handling.

info-971-315

 

5. DPF Indicator Light - Particulate Filter Indicator Light

 

info-838-152

 

The DPF indicator light includes the DPF regeneration indicator light and the DPF regeneration prohibition indicator light. The display forms of the lights are mainly yellow flashing, constantly on, and red.

1) DPF regeneration indicator light - yellow + flashing: It indicates that parking regeneration is required. The vehicle needs to be parked at a safe location for parking regeneration. The blue arrow in the lower right corner of Figure 1 points to the parking in-place forced regeneration switch.

2) DPF regeneration indicator light - yellow + constantly on: It indicates that the vehicle is regenerating, either while driving or during parking.

3) DPF regeneration indicator light - red + constantly on: It indicates that service regeneration is required. The vehicle needs to be taken to a service station for service regeneration.

4) DPF regeneration prohibition indicator light - red + constantly on: It indicates that regeneration is prohibited. Press the regeneration prohibition switch at a gas station or in a dangerous area. When the regeneration prohibition indicator light on the instrument panel shows a red light flashing or constantly on, there will be corresponding annotations on the instrument panel.

The lighting forms and classification of the DPF light are shown in the following table:

 

info-670-467

 

Note: During the active forced regeneration while the vehicle is stationary, the exhaust temperature of the engine is extremely high. Please be sure to avoid flammable and explosive areas and other dangerous zones.

 

6. High Exhaust Temperature Indicator Light

 

info-95-79

When this light is on while driving, it indicates that the DPF of the engine is undergoing driving regeneration. The driver does not need to perform any other operations. Note: If passing through flammable and explosive areas, please press the "Regeneration Prohibition Switch" indicated by the red arrow in the lower right corner of Figure 1. After leaving the dangerous area, press this switch again to reset. 7.

 

7.DWS Indicator Light Driver Warning Indicator Light

 

info-100-89

When this light is on, it indicates that there is a fault related to the control of nitrogen oxide emissions. The vehicle's torque will be restricted and its speed limited. Please have it repaired as soon as possible.

Send Inquiry