+86-15123173615

What fault phenomena will occur if the sensor is damaged?

Oct 29, 2026

1. Damage phenomenon of intake pressure and temperature sensor:

① In the ON position, the engine fault light remains constantly on; ② When gently stepping on the accelerator at idle speed, a small amount of black smoke is emitted; when accelerating abruptly, a large amount of black smoke is emitted; ③ The engine lacks power; ④ Fault code: P01D6 (Intake pressure sensor voltage is below the lower limit). Analysis of the cause: The intake pressure signal is abnormal, and the ECU cannot receive the correct intake volume information, resulting in abnormal fuel injection, insufficient combustion, and lack of engine power. Black smoke is emitted during refueling. Problems with the wiring connection and sensor failure can both cause this fault. Solution: Check the intake pressure and temperature sensor.

2. Damage phenomenon of water temperature sensor:

① In the ON position, the engine fault light remains constantly on; ② The water temperature always shows the maximum value of 120℃; ③ Engine torque limitation and lack of power; ④ Fault code: P003D (Water temperature sensor voltage is below the lower limit value). Analysis of the cause: The water temperature sensor fails. When the ECU detects that the output signal of the water temperature sensor is unreliable, it uses an alternative value. For the purpose of protecting the engine, the ECU limits the engine's torque. Solution: Check the water temperature sensor.

3. Damage phenomenon of oil pressure sensor:

① After starting, the oil pressure indicator light remains constantly on; ② Engine fault light remains constantly on; ③ Idle speed, the oil pressure value shows 0.99; ④ Fault code: P01CA (Oil pressure sensor voltage is above the upper limit). Analysis of the cause: The probe of the oil pressure sensor is severely damaged, and the ECU detects that the output signal of the oil pressure sensor is unreliable, using an alternative value. For the purpose of protecting the engine, the ECU limits the engine's torque. Solution: Check the oil pressure sensor.

4. Poor contact phenomenon of OBD socket terminal:

① In the ON position, the diagnostic instrument has normal power supply, but it cannot enter the ECU to read relevant information; ② No fault code. Analysis of the cause: The OBD socket terminal is disconnected, resulting in poor contact, and the diagnostic instrument cannot communicate with the ECU. Solution: Check the OBD socket terminal.

5. Short circuit phenomenon of the after-treatment heating relay box:

① After starting, the OBD fault light remains constantly on; ② Engine torque limitation and lack of power; ③ Fault code: P0050 (Downstream nitrogen oxide sensor CAN signal reception timeout), P018C (Downstream nitrogen oxide sensor preparation timeout). Analysis of the cause: The nitrogen oxide sensor wiring is worn and short-circuited, grounding, and the nitrogen oxide sensor cannot work properly, resulting in emission超标, engine torque limitation, and system alarm. Solution: Check the nitrogen oxide sensor wiring.

6. Damage phenomenon of the after-treatment heating relay box:

① After starting, the OBD fault light is on; ② Fault code: P028F (Urea pressure pipe heating relay control end open circuit fault). Analysis of the cause: The wiring is broken. Solution: Check and repair the wiring of the heating relay box.

7. Open circuit fault phenomenon of the urea supply unit drive circuit:

① After starting, the OBD fault light remains constantly on; ② Engine torque limitation and lack of power; ③ Fault code: P3006 (Urea supply unit drive circuit open circuit fault); ④ No consumption of urea. Analysis of the cause: The control line of the urea pump is broken, specifically manifested as the 10th pin of the electrical connector of the urea pump is disconnected, the urea pump does not work, the system cannot normally spray urea, resulting in emission超标, engine torque limitation, and system alarm.

Solution: Check the urea pump wiring connector.

8. Software error at the bottom layer of the instrument does not send the vehicle speed signal phenomenon:

① During uphill driving or sudden acceleration, the engine power will temporarily decrease for 1-2 seconds; ② No fault code. Analysis of the cause: During driving, the vehicle speed signal sent by the instrument suddenly drops to 0, the change of the vehicle speed signal causes the ECU to control the fuel quantity change, resulting in a transient cut-off of fuel. Solutions: If the matching instrument part number of the vehicle is 3820010-61B, please update it to the latest version of the instrument, with the part number being 3820010D61B.

9. Fault phenomenon of SCR system urea return pipe blockage:

① After starting, the OBD fault light remains on constantly; ② Engine torque limitation and lack of power; ③ Fault code: P0207 (SCR system urea return pipe blockage fault); ④ No urea consumption. Cause analysis: Foreign matter blocking in the urea return pipe, resulting in the system being unable to spray urea normally, exceeding emission standards, engine torque limitation, and system alarm. Solution measures: Check the urea return pipe (the urea pipe between the urea pump and the urea tank).

10. Fault phenomenon of urea return heating pipe connector terminal plug-in misalignment:

① After starting, the OBD fault light remains on constantly; ② Fault code: P0287 (Urea return pipe heating relay load end and the power supply between the circuit have open circuit or ground short circuit faults). Cause analysis: Remove the urea heating return pipe connector plug-in, and it is found that the terminal is misaligned. Solution measures: Repair the terminal and reinsert the connector plug-in.

11. Fault phenomenon of urea pressure pipe open circuit:

① After starting, the OBD fault light remains on constantly; ② Fault code: P028E (Urea pressure pipe heating relay load end and the power supply between the circuit have open circuit or ground short circuit faults); ③ The engine may have torque limitation and lack of power in winter. Cause analysis: The heating wire of the urea pump pressure pipe is broken, resulting in the inability to normally heat urea in winter, and the system alarms. Solution measures: Check the urea pump pressure pipe (the urea pipe from the urea pump to the urea nozzle).

12. Fault phenomenon of urea suction pipe open circuit:

① After starting, the OBD fault light remains on constantly; ② Fault code: P029A (Urea suction pipe heating relay load end and the power supply between the circuit have open circuit or ground short circuit faults); ③ The engine may have torque limitation and lack of power in winter. Cause analysis: The heating wire of the urea pump suction pipe is broken, resulting in the inability to normally heat urea in winter, and the system alarms. Solution measures: Check the urea pump suction pipe (the urea pipe from the urea tank to the urea pump).

13. Fault phenomenon of urea return pipe open circuit:

① After starting, the OBD fault light remains on constantly; ② Fault code: P0287 (Urea return pipe heating relay load end and the power supply between the circuit have open circuit or ground short circuit faults); ③ The engine may have torque limitation and lack of power in winter. Cause analysis: The heating wire of the urea pump return pipe is broken, resulting in the inability to normally heat urea in winter, and the system alarms.

Solution measures: Check the urea pump return pipe (the urea pipe from the urea pump to the urea tank).

14. Leakage of urea from the urea pump electrical connector position:

① After starting, the OBD fault light is on; ② Engine torque limitation and lack of power; ③ No urea consumption; ④ Fault codes: P0227, P0228, P01FC, P01FB, P02B1, P02A1, P01FA, P01FB (Please refer to the maintenance manual for the corresponding information of the fault codes). Cause analysis: Leakage of urea at the urea pump electrical connector position, corroding the metal pins, resulting in short circuit or open circuit faults in the circuit. (In severe cases, the rail pressure sensor may be burned out, and the rail pressure sensor and the internal pressure sensor of the urea pump share the same power supply path in the ECU). Solution measures: Check the urea pump electrical connector, and replace the damaged part.

15. Breakage of the exhaust temperature sensor wiring harness:

① After starting, the OBD fault light is on; ② Engine torque limitation and lack of power; ③ No urea consumption; ④ Fault code: P027B (SCR catalyst upstream temperature sensor signal voltage is too high fault). Reason Analysis: The wiring harness of the exhaust temperature sensor was broken, preventing the ECU from obtaining the upstream exhaust temperature of the SCR catalyst, resulting in the urea pump not building pressure and not consuming urea, which led to excessive emissions, engine torque limitation, and system alarms. Solution: Repair the wiring harness and wrap it properly.

16. Reverse connection of the crankshaft sensor and fuel metering unit connectors:

① The maximum speed was limited to 1800 rpm; ② The start-up time was too long; ③ Fault codes: P00EF (crankshaft sensor without signal), P01E2 (pressure relief valve opened). Reason Analysis: The connectors of the crankshaft sensor and fuel metering unit were connected in reverse, and neither could provide normal signals to the ECU. Solution: Swap the connectors of the crankshaft sensor and fuel metering unit.

17. Persistent open state of the anti-freezing liquid electromagnetic valve of the urea tank:

The urea tank temperature was high, and urea was discharged from the venting plug. Reason Analysis: During driving, the anti-freezing liquid electromagnetic valve of the urea tank was always open, meaning the anti-freezing liquid was continuously defrosting the urea tank. ① There were impurities in the coolant, accumulating near the diaphragm, and the impurities squeezed the diaphragm, creating depressions that affected the seal; ② The working pressure range of the electromagnetic valve did not match the actual pressure value. (Currently, the working pressure of the electromagnetic valve is 20kPa to 250kPa, while the actual pipeline pressure may be lower than 20kPa. When the pressure is lower than 20kPa, the diaphragm cannot be tightened and cannot effectively seal.)

Solution: Replace the electromagnetic valve assembly with the latest version according to the parts catalog.

18. Excessively sensitive nitrogen oxide sensor concentration limit in engine bench calibration:

For Russian J6 export vehicles (common rail system), the nitrogen oxide sensor falsely reported faults at the highest frequency. Similar problems also occurred in domestic common rail systems: ① The OBD fault light was constantly on after startup; ② Engine torque limitation and lack of power; ③ Fault codes: P01FC: NOx peak check fault, P01FF: NOx increment check fault. Reason Analysis: The nitrogen oxide NOx concentration limit was not calibrated properly, and the threshold was too sensitive. The peak calibration limit should be changed from 200ppm to 50ppm, and the signal change range should be changed from 400ppm to 50ppm. Solution: Write the latest version of data.

19. Permanent fault of the motor speed deviation of the urea supply unit:

① The OBD light was on, and torque limitation was not allowed; ② Fault code: P02AB (permanent fault of the urea supply unit motor speed deviation). Reason Analysis: The urea pump motor was damaged. Solution: Replace with BOSCH 2.2 generation urea pump 1161010-51B.

20. Crystallization at the urea nozzle seat:

Uniform crystallization occurred at the urea nozzle seat, with the middle nozzle hole not blocked and able to ventilate.

Reason Analysis: There was local swirling at the urea nozzle seat, causing a thin layer of urea crystallization. Solution: This is a normal phenomenon. If it does not affect emissions, no treatment is required.

21. Crystallization at the intake port of the post-treatment device:

Uniform crystallization occurred at the intake port of the post-treatment device, without large chunks of crystalline urea.

Reason Analysis: During use, a thin layer of urea crystallization was generated near the interface between the post-treatment device and the intake pipe. Solution: This is a normal phenomenon. If it does not affect emissions, no treatment is required.

22. Quality problem of the intake control component of the post-treatment device:

① The OBD light was on; ② The vehicle was torque-limited and lacked power; ④ The urea was not consumed. Reason Analysis: The welding of the urea nozzle seat and the exhaust pipe was offset, resulting in "double eyelid" and causing urea crystallization, which then blocked the exhaust pipe.

Solution: Polish the "double eyelid" area.

23. Crystallization and blockage of the urea nozzle head:

① After startup, the OBD fault light was constantly on; ② Engine torque limitation and lack of power; ④ The urea was not consumed; ⑤ The urea nozzle head was crystallized, and the nozzle hole was blocked. Reason Analysis: The angle between the urea nozzle seat and the exhaust pipe did not meet the engineering design specifications of BOSCH system.

Solution: Replace the new condition exhaust pipe.

24. The plug of the camshaft sensor is not inserted, resulting in difficulty in starting the engine:

① After starting, the OBD fault light remains constantly on; ② The engine starts with difficulty; ③ Fault code: P0032 - CAN B passive fault, P00EC - no detection of camshaft signal. Analysis of the cause: ① The CAN B passive fault is a data issue and should be shielded; ② No camshaft signal, which makes it impossible to accurately determine the cylinder number during startup, causing difficulty in starting.

Solution: ① For the P0032 fault, re-write the latest version of the electronic control data released after September 2014 and shield this fault code; ② For the P00EC fault, check the camshaft sensor plug.

Send Inquiry